Loose or Twisted Cable is one of the causes of an accident

Many electrical problems in the home may be traced back to different variations of the same basic issue: wire connections that have been made incorrectly or have loosened over time. You may have inherited the issue from a former owner or an electrician who did a poor job, or it could be the consequence of the work you performed yourself.

Many wire connection issues are not the fault of anyone, but rather the product of time. Wires go through a continual cycle of expansion and contraction as they heat and cool. Every time a switch is turned on or an appliance is plugged in, the natural effect is that wire connections loosen over time.

A single unsecured wire can cause a circuit breaker to trip (or a fuse to blow). Even if the wire is still attached to an outlet, but the terminal screw on the outlet isn’t tightened enough, this can happen. In other cases, totally unsecured wires may come into touch with electrical boxes or other wires, causing a tripped breaker—or worse.

Because the breaker does not always trip and shut off the electricity, loose and unconnected wires might become hot enough to start fires or cause major shock dangers.

Dangers of a loose wire

To create a secure connection, wires are connected to outlets (technically termed receptacles) using screw terminals or other devices. Tightly connected wires produce good electrical contact, allowing electricity to travel through with minimal resistance. There is more resistance if the terminal is not tight and the wire is not squeezed against the terminal’s metal contact. And heat is created by resistance. The higher the heat, the looser the connection.

The heat from a loose connection can trip the circuit breaker if it is strong enough or lasts long enough, however, this is rare. A standard breaker will only trip if the load is too big or if the electrical path is shorted (a short circuit). The tough issue is that you might not even realize there’s a problem with the circuit.

A conventional circuit breaker may or may not trip due to a loose wire connection. This is one of the reasons why arch-fault circuit interrupters, or AFCIs, are required in new homes today. These are intended to detect and turn off the electricity in the event of the most common types of arc faults in residential wiring. In a nutshell, AFCIs aid in the prevention of house fires caused by arc faults.

With recent code requirement modifications, AFCI protection is now required on circuits supplying bedrooms, corridors, living rooms, and most other living areas in a home. They were formerly only required in bedrooms.

Dangers of twisted cable

Wires or cables that aren’t working should be removed right away. Frayed, loose, or exposed wires in cables should be addressed and replaced. Electric shocks and flames can be caused by damaged wires and cables.

Extension cords are prone to cracks and other flaws, which can cause shocks. And there’s no way to fix these issues with electrical tape. Rather than using an extension cord, be careful and place your electrical gadgets within reach of an electrical outlet.

Twisted cables must be secured to prevent injury to your family members. Children can easily bite down on cables, electrocuting themselves, while older children and adults might suffer twisted or broken ankles as a result of accidents or falls. Children can readily grab cords that are dangling from the ceiling or walls, posing an electrical hazard. Cables that are squished into tiny spaces or that have built-up pressure, on the other hand, can be a fire hazard. Keep your wires out of sight but resting flat to avoid pressure on them to avoid these problems.

To keep things neat, many desk employees staple cords to their cubicles. If you’re not careful, staples can cause catastrophic cord damage and even electrical shock. The best approach to manage office wire is to use cable covers that keep your power cords out of harm’s way without creating a fire or other problem. Do not, under any circumstances, leave electrical wires strewn around your desk or office. You may be held accountable for any injuries that occur in or near your office due to the danger of tripping and electrical hazards. Keep them safely out of the path to be on the safe side.

How to prevent accidents caused by the loose and twisted cable

  • Many parents cover unused outlets to protect their children from shock, but this isn’t enough. Small children gnawing, tripping, and pulling on household cables pose the same dangers as inserting fingers or sharp objects into electrical outlets. Lifting wires off the floor and out of your children’s reach is one of the simplest methods to safeguard them from cable-related injury. Cords may be simply routed under doorframes, behind furniture, and held against the higher surface. A surface raceway, another child-safety favorite, is the ideal solution for containing and concealing wire runs between your gadgets and power outlets.
  • The devices that make modern business possible, from computers and phones to fax machines and copiers, come with a slew of cable-related tripping hazards! The tangles of cords that scurry over office floors are a disaster waiting to happen. Increase your employee safety factor with light capacity floor cord coverings to save the money, annoyance, and downtime that accidents can bring.
  • A split wire loom, a flexible and robust polyethylene corrugated tube with a split down the side where you input your multi-cable bundle, may quickly shield computer cables for a few dollars. If you need to add another wire later, you can easily slip it in with the others in the split wire loom without having to remove the entire bundle.


We hope this article helped you regarding cable management and how to avoid hazards caused by loose or twisted cables at your home or workplace. Having the minimum basic electrical knowledge is essential for all of us to maintain safety, and thus avoiding loose or twisted cables is always the best thing to do.

Similar Articles